--- title: "Common Network Debugging Commands" date: 2022-01-02T15:17:02-05:00 draft: false tags: ["Networking"] math: false medium_enabled: true --- Below are list of commands that I use to debug common issues in a network. There is a wonderful tool called Wireshark which you can use to sniff packets in a network and filter by a wide range of options, but we'll mainly focus on simple tools that you can use in the terminal. ## `ping` The most commonly used networking command is `ping`. This allows you to see the time it takes to send and receive an ICMP packet from/to a specified address. Most people use Google's DNS server `8.8.8.8` as a quick test to see if they have access to the Internet. ```bash ping 8.8.8.8 ``` ``` PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_seq=1 ttl=117 time=267 ms 64 bytes from 8.8.8.8: icmp_seq=2 ttl=117 time=74.9 ms 64 bytes from 8.8.8.8: icmp_seq=3 ttl=117 time=34.7 ms 64 bytes from 8.8.8.8: icmp_seq=4 ttl=117 time=298 ms ``` Press CTRL-C when you are done looking at the output. Here is a list of common flags used in the ping command. | Flag | Description | | ------------ | ------------------------------------------------------------ | | `-c NUM` | Only send/receive an ICMP packet `NUM` number of times | | `-D` | Print the timestamp along with the roundtrip time | | `-W timeout` | Waits a `timeout` amount of seconds for the response before moving on to the next ICMP roundtrip | Example: ```bash ping -c3 -D -W1 1.1.1.1 ``` ``` PING 1.1.1.1 (1.1.1.1) 56(84) bytes of data. [1641156381.342990] 64 bytes from 1.1.1.1: icmp_seq=1 ttl=57 time=52.6 ms [1641156382.555358] 64 bytes from 1.1.1.1: icmp_seq=2 ttl=57 time=263 ms [1641156383.327286] 64 bytes from 1.1.1.1: icmp_seq=3 ttl=57 time=34.3 ms --- 1.1.1.1 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2003ms rtt min/avg/max/mdev = 34.275/116.670/263.116/103.823 ms ``` ## `ip route` Without any extra flags or subcommands this will give you a view of your routing table. A routing table specifies for a given address range, which device to send the network traffic over. Normally you see a large routing table inside businesses (or if you access a lot of VPNs at once). Here is an example of a typical one in a household. ```bash ip route ``` ```bash default via 192.168.0.1 dev wlan0 proto dhcp metric 600 192.168.0.0/24 dev wlan0 proto kernel scope link src 192.168.0.2 metric 600 ``` This says that any address between 192.168.0.1-254 goes over the `wlan0` device which on some computers denote WiFi. The first line shows what the default entry/gateway is, that is if the ip address you're trying to access is not listed in the table it will go through the IP listed in that row first. You can manually add and remove entries in the routing table as well. Example: ```bash sudo ip route add 192.168.1.0/24 dev wlan0 ``` ```bash sudo ip route del 192.168.1.0/24 dev wlan0 ``` ## `traceroute` This command is more useful if you have multiple segmented networks and you're trying to figure out at which layer the connection failed. Recently I used this to debug some directional WiFi extenders. ```bash traceroute 8.8.8.8 ``` ```bash traceroute to 8.8.8.8 (8.8.8.8), 64 hops max 1 192.168.0.1 2.051ms 2.003ms 1.278ms 2 192.168.2.1 5.743ms 5.647ms 3.592ms 3 192.168.5.1 5.754ms 63.285ms 7.187ms 4 72.126.142.1 96.056ms 101.861ms 14.547ms 5 103.51.11.206 87.273ms 16.617ms 72.810ms 6 170.222.220.217 13.745ms 101.122ms 16.402ms 7 201.149.23.6 85.738ms 102.977ms 100.974ms 8 107.150.228.33 15.111ms 87.467ms 103.076ms 9 12.21.20.233 100.755ms 102.000ms 102.352ms 10 8.8.8.8 102.505ms 102.085ms 101.762ms ``` ## `dig` We've been talking about IP addresses with the last few commands, but there can be problems in the domain name resolution as well. A domain name is what you commonly type in the browser such as `duckduckgo.com`. Your computer will then ask the DNS server it knows about what the IP of that address is. ```bash dig duckduckgo.com ``` ``` ; <<>> DiG <<>> duckduckgo.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 36469 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 1 ;; OPT PSEUDOSECTION: ; EDNS: version: 0, flags:; udp: 65494 ;; QUESTION SECTION: ;duckduckgo.com. IN A ;; ANSWER SECTION: duckduckgo.com. 149 IN A 52.149.246.39 ;; Query time: 88 msec ;; SERVER: 127.0.0.53#53(127.0.0.53) ;; WHEN: Sun Jan 02 16:06:23 EST 2022 ;; MSG SIZE rcvd: 59 ``` Most linux systems have a DNS cache server setup which makes it difficult to figure out what the upstream DNS server that it's querying is. Mainly because it can be configured a myriad of ways. If you are using NetworkManager you can use the following command: ```bash nmcli dev show | grep DNS ``` In some other cases it would be in `/etc/resolv.conf` ```bash cat /etc/resolv.conf ``` ## `arp` Lastly at the lowest level, arp will tell you the MAC addresses of IP addresses you have communicated with before. ```bash arp ``` ``` Address HWtype HWaddress Flags Mask Iface 192.168.0.1 ether 10:1d:b1:1d:1f:91 C wlan0 192.168.0.11 ether 72:25:22:2c:72:72 C wlan0 192.168.0.111 ether 03:33:34:3b:23:39 C wlan0 ```